1. Check the bearing temperature frequently. If the temperature is too high, check whether the lubrication and transmission parts are normal, and whether the rolling distance is too tight. Find out the causes in time, take corresponding measures, and stop the machine for inspection when the situation is serious.

經常檢查傳動帶的松緊程度，皮帶過松會(huì )降低傳動效率而影響研磨效果，過緊則容易引起軸承發熱，增加動力消耗，降低傳動帶的使用壽命。

Often check the tightness of the belt. Too loose belt will reduce the transmission efficiency and affect the grinding effect. Too tight belt will easily cause bearing heating, increase power consumption and reduce the service life of the belt.

各種傳動部件必須緊固可靠，拆卸或安裝應使用專用工具，禁止用手錘等工具直接擊打。

All kinds of transmission parts must be fastened and reliable. Special tools shall be used for disassembly or installation. It is forbidden to strike directly with hammers and other tools.

不忘檢查氣動元件，要經常檢查氣路中各氣動元件，氣路及連接處是否有漏氣或損壞，同時要檢查供氣壓力是否符合要求，對同步帶 的使用情況也要經常檢查，若發現過緊、過松、跳動、跑偏、磨損嚴重等情況，應及時調整、檢修或更換。

Do not forget to check the pneumatic components. Always check the pneumatic components in the air circuit, whether there is leakage or damage in the air circuit and the connection. At the same time, check whether the air supply pressure meets the requirements. The use of the synchronous belt should also be checked frequently. If it is found that it is too tight, too loose, jumping, deviation, serious wear and other conditions, it should be adjusted, repaired or replaced in time.

定期有序地更換面粉機磨輥，磨輥不能一次更換過多，同時磨輥的直徑不能差別過大，齒輥的角、斜度、齒數要與規定相符，要留有一定的齒頂平面。光輥各段錐度要 準確且符合規定要求，表面粗糙度要均勻一致。更換磨輥后，應按各系統磨粉機的要求，用塞尺檢查，粗調其軋距。

Replace the mill roll regularly and orderly. The mill roll should not be replaced too much at one time. At the same time, the diameter of the mill roll should not be too different. The angle, slope and number of teeth of the toothed roll should be consistent with the regulations, and a certain tooth top plane should be left. The taper of each section of the smooth roller shall be accurate and meet the specified requirements, and the surface roughness shall be uniform. After replacing the grinding roller, check with feeler gauge and roughly adjust the rolling distance according to the requirements of grinding machine of each system.

本文由豆漿石磨機為您提供，我們的網站是：http://www.jylmjz.com將以全心全意的熱情為您提供服務，歡迎您的訪問！

This article is provided for you by soybean milk stone mill http://www.jylmjz.com We will serve you wholeheartedly and warmly. Welcome to visit!